Note<\/strong>: The ethernet port use a passive PoE standard, please check if your device is compatible before connecting to avoid damage to the hardware.<\/p><\/div><\/div>\n\n\n Locate the tripod on a stable position away from buildings, trees or other tall objects to prevent multipath or satellite coverage effects. To improve the range of the radio modems the antenna should be located as high as possible.<\/p>\n\n\n Before powering up the GNSS Base Station, the antennas must be connected with the supplied cables. The cables and interfaces are marked with \u201cRadio Modem\u201d or \u201cGPS Antenna\u201d. Make sure not to swap the connectors to prevent a hardware damage.<\/p>\n\n\n\n Note<\/strong>: After powering it up by using the power button inside of the GNSS Base Station, a hardware test is conducted and all components are initialized. The following LEDs shine jointly during initialization: When initialization is complete, the following LED\u2019s turn off: The operating terminal is ready for use. The GNSS receiver is initialized automatically. A progress bar in the \u201dSetup\u201d display indicates the current initialization status. The receiver\u2019s initialization should be finished in 5 minutes. On successful initialization, this display is replaced by the main menu.<\/p>\n\n\n\n When the GNSS Base Station is started, the \u201dInformation\u201d display indicates the internal GNSS receiver\u2019s solution status. This provides information on the current position solution. Status information \u201d0\u201d indicates that a valid position solution was calculated. All the settings in the Setup <\/em><\/strong>display can be adapted easily via the keypad.<\/p>\n\n\n The GNSS antenna\u2019s position can be determined via the menu item Auto Pos Setup<\/em><\/strong>. Optionally the averaging time or the required accuracy can be specified.<\/p>\n\n\n\n Note<\/strong>: An averaging time between 0.01 and 100 hours is entered via the keypad. In this mode, position values are averaged over the specified time period, and the final position calculated to a corresponding degree of precision.<\/p>\n\n\n\n Current values during the averaging process are indicated on the information display.<\/p>\n\n\n\n The required accuracy in meters (the permissible value range here is also 0.01 – 100) is entered via the keypad. In this mode, averaging is finished on attainment of the required accuracy. If the specified accuracy cannot be achieved, averaging is finished after 100 h.<\/p>\n\n\n\n Current values during the averaging process are indicated on the information display.<\/p>\n\n\n\n Averaging is ended automatically on attainment of the specified parameter, or after 100 hours have elapsed. When averaging is complete, you are asked whether the averaged position should be applied. If so, then correction data are transmitted automatically.<\/p>\n\n\n\n It is possible to terminate averaging ahead of time by pressing the ESC key. In this case, the device applies the averaged position which was determined so far.<\/p>\n\n\n\n The result of averaging can be saved for further use, e.g. if measurements are usually conducted at a certain location.<\/p>\n\n\n\n The GNSS Base Station can be operated without position averaging by selecting the Fix recent pos<\/em><\/strong> menu item. This mode is useful if the ADMA\u2019s relative position (over a certain time period or with respect to other ADMAs) is of interest instead of the ADMA\u2019s absolute position.<\/p>\n\n\n\n This option is useful if details concerning the GNSS antenna\u2019s position are available, e.g. due to land survey data by a state authority. If the GNSS Base Station accepts the entry, then correction data are transmitted automatically.<\/p>\n\n\n\n If the GNSS Base Station is operated in stationary mode, it is expedient to set the Fix permanent <\/em><\/strong>parameter to YES<\/em><\/strong> so that the currently or previously fixed position is saved. In this case, all configuration settings are preserved. This has the advantage that in the event of a voltage loss, the stationary GNSS Base Station is restored to the selected operating mode.<\/p>\n\n\n\n Note<\/strong>: Via the menu item Load\/Save Position<\/em><\/strong>, it is possible to save up to 10 positions on the SD card and read them into the GNSS Base Station. Positions can only be saved in the CORRECTION DATA TRANSMIT<\/em><\/strong> mode (the control LED remains solidly lit). In this mode, the position indicated by the information display is saved on the SD card.<\/p>\n\n\n\n Position can be retrieved from the SD card under the menu item Load Position<\/em><\/strong>. The saved positions are labelled position 0 to position 9. When a position is selected, it appears in the Setup<\/strong><\/em> display. When confirmed, this position is taken over by the Information<\/strong><\/em> display, and correction data are transmitted. It is also possible to access the SD card via the USB interface of the GNSS Base Station. In this case, the SD card serves as a USB stick. This connection permits position data on the SD card to be viewed and modified where necessary.<\/p>\n\n\n\n The following IP settings can be done at the GPS Base Station:<\/p>\n\n\n\n IP-Address and IP-Mask<\/strong> Dest.IP-Address<\/strong>![\"\"](\"https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/image-73.jpg\")
<\/figure>\n<\/div>\n\n\nMounting the tripod and antennas<\/h2>\n\n\n\n
![\"\"](\"https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/image-73.png\")
<\/figure>\n<\/div>\n\n\n
Each time the GNSS Base Station\u2019s antenna is relocated, its position must be averaged again or – if it was already determined precisely on a previous occasion – the relevant data must be loaded from the appropriate file.<\/p><\/div><\/div>\n\n\n\nPowering Up<\/h2>\n\n\n\n
\u2022 CORRECTION DATA TRANSMIT<\/em><\/strong>
\u2022 AVERAGING POSITION<\/em><\/strong>
\u2022 GNSS ERROR<\/em><\/strong><\/p>\n\n\n\n
\u2022 CORRECTION DATA TRANSMIT<\/em><\/strong>
\u2022 AVERAGING POSITION<\/em><\/strong><\/p>\n\n\n\nStatus Information<\/h2>\n\n\n\n
Normally it takes less than one minute to receive the status information \u201c0\u201d. In some situation it can take round about 25 minutes. For example, if the location of the GNSS Base Station changed significantly or if it has been turned off for a long time.<\/p>\n\n\n\nOperation via Keypad<\/h2>\n\n\n\n
![\"\"](\"https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/image-74.jpg\")
<\/figure>\n<\/div>\n\n\nDetermining the position<\/a><\/h2>\n\n\n\n
Position averaging<\/h3>\n\n\n\n
To guarantee error-free averaging, the GNSS Base Station should be operated with GNSS reception for at least 15 minutes prior to commencement of position averaging. This time is needed by the receiver to obtain the necessary data from the GNSS satellite.<\/p><\/div><\/div>\n\n\n\nSpecification of averaging time<\/h4>\n\n\n\n
Specification of accuracy<\/h4>\n\n\n\n
End of averaging<\/h4>\n\n\n\n
Fix recent position<\/h3>\n\n\n\n
Manual position entry<\/h3>\n\n\n\n
Under the menu item \u201dManual Pos Setup\u201d, it is possible to notify the GNSS Base Station of the current position via the keypad. In this process, make sure that the specified position matches that of the antenna as closely as possible. The current position should be indicated by the information display. If the specified position deviates by more than 50 m from the current position, the data will not be applied by the GNSS Base Station.<\/p>\n\n\n\nStationary operating mode<\/a><\/h2>\n\n\n\n
If the location of the GNSS Base Station is changed while in the Fix Permanent<\/em><\/strong> mode, the display outputs an error message that the fixed position does not match the current position. In this case, delete the fixed position via the Configuration \/ Unfix Position<\/em><\/strong> menu item.<\/p><\/div><\/div>\n\n\n\nStoring and retrieving position data<\/a><\/h2>\n\n\n\n
Saving position data<\/h3>\n\n\n\n
Retrieving saved position data<\/h3>\n\n\n\n
If the position data saved are incorrect for the current location, i.e. if the Information<\/strong><\/em> display deviates too much from the current location\u2019s values, the data are not applied by the GNSS Base Station. Then the GNSS ERROR<\/strong><\/em> LED turns on.<\/p>\n\n\n\nIP Settings<\/h2>\n\n\n\n
Defines the own IP address and Subnetmask, input in in dotted-decimal notation.
Defaults
IP-Address<\/em><\/strong>: 192.168.88.23
Subnetmask<\/em><\/strong>: 255.255.255.0<\/p>\n\n\n\n
This address is the receiver IP of the correction data output.
The IP address and Port used to deliver packets of data across a network and have what is termed end-to-end significance. This means that the source and destination IP address remain constant as the packet traverses a network.
To use the Ethernet Broadcast function set the last character to 255.<\/p>\n\n\n\n