{"id":23202,"date":"2023-01-30T15:01:06","date_gmt":"2023-01-30T14:01:06","guid":{"rendered":"https:\/\/genesys-offenburg.de\/?post_type=smart-docs&#038;p=23202"},"modified":"2023-06-23T10:06:23","modified_gmt":"2023-06-23T08:06:23","slug":"start-adma-measurement","status":"publish","type":"smart-docs","link":"https:\/\/genesys-offenburg.de\/en\/support\/adma-manual\/adma-configuration\/start-adma-measurement\/","title":{"rendered":"Start ADMA measurement"},"content":{"rendered":"\n<p>Basically, there are 4 possibilities to start a measurement:<br>\u2022 Webinterface menu <strong>6\ufe0f\u20e3 LOAD\/SAVE\/START<\/strong> command Start measurement.<br>\u2022 the main menu\u2019s item Remote Start in ADMA System Software<br>\u2022 via the Autostart mode<br>\u2022 a user specific tool (CAN, COM or Ethernet command)<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Start measurement via Webinterface \/ System Software<\/h2>\n\n\n\n<p>Before starting a measurement please enter the start course and the pre-alignment. For further information about these two parameters look up the Ariclte <a href=\"https:\/\/genesys-offenburg.de\/support\/adma-manual\/measuring-procedure\/initialization-procedure\" target=\"_blank\" rel=\"noreferrer noopener\">Initialization procedure<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Autostart mode<\/h2>\n\n\n\n<p>The setting <em>Autostart <\/em>can be enabled in configurations dialog <strong>1\ufe0f\u20e3 BEHAVIOUR<\/strong>. If <em>Autostart <\/em>is activated, the ADMA automatically starts data acquisition after power on. Depending on your choice in configurations dialog <em><strong>Interface<\/strong><\/em>, data will be transmitted via CAN, Ethernet or COM interface.<\/p>\n\n\n\n<div class=\"wp-block-smartdocs-notice\"><div class=\"smartdocs-block-notice notice-info\"><p><strong>Note<\/strong>: The ADMA in Autostart mode takes a minimum of 15 seconds to switch to pre-alignment or measuring mode. During this time, the internal GNSS-Receiver is booting up and therefore configuration is not possible.<\/p><\/div><\/div>\n\n\n\n<h2 class=\"wp-block-heading\">Start a measurement via a user specific tool<\/h2>\n\n\n\n<p>Data acquisition can also be started via a user specific tool. The interface protocol for the COM, CAN and Ethernet interface is available at the article <strong>Start measurement via command<\/strong> (Verlinkung TBD). <br>The command message sequence of CAN remote start can be found in the Technical Documentation.<\/p>\n\n\n\n<div class=\"wp-block-smartdocs-notice\"><div class=\"smartdocs-block-notice notice-info\"><p><strong>Note<\/strong>: At <strong>8\ufe0f\u20e3 Load\/Save\/Start<\/strong> it is possible to check if the ADMA measurement is already started via <em>Measurement mode active<\/em> value.<\/p><\/div><\/div>\n\n\n<div class=\"wp-block-image\">\n<figure class=\"aligncenter size-full\"><img decoding=\"async\" width=\"524\" height=\"215\" src=\"https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/Bild_2022-05-16_132852357.png\" alt=\"\" class=\"wp-image-23212\" srcset=\"https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/Bild_2022-05-16_132852357.png 524w, https:\/\/genesys-offenburg.de\/wp-content\/uploads\/2022\/05\/Bild_2022-05-16_132852357-300x123.png 300w\" sizes=\"(max-width: 524px) 100vw, 524px\" \/><figcaption class=\"wp-element-caption\">Webinterface: 8\ufe0f\u20e3 <strong>Load\/Save\/Start<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n<p><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Basically, there are 4 possibilities to start a measurement:\u2022 Webinterface menu 6\ufe0f\u20e3 LOAD\/SAVE\/START command Start measurement.\u2022 the main menu\u2019s item Remote Start in ADMA System Software\u2022 via the Autostart mode\u2022 a user specific tool (CAN, COM or Ethernet command) Start measurement via Webinterface \/ System Software Before starting a measurement please enter the start course [&hellip;]<\/p>\n","protected":false},"author":148,"featured_media":30266,"template":"","meta":{"_acf_changed":false,"_links_to":"","_links_to_type":0,"footnotes":""},"smartdocs_category":[809,844,848],"class_list":{"0":"post-23202","1":"smart-docs","2":"type-smart-docs","3":"status-publish","4":"has-post-thumbnail","6":"smartdocs_category-adma-manual","7":"smartdocs_category-adma-configuration","8":"smartdocs_category-measuring-procedure"},"acf":[],"_links":{"self":[{"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/smart-docs\/23202","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/smart-docs"}],"about":[{"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/types\/smart-docs"}],"author":[{"embeddable":true,"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/users\/148"}],"version-history":[{"count":0,"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/smart-docs\/23202\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/media\/30266"}],"wp:attachment":[{"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/media?parent=23202"}],"wp:term":[{"taxonomy":"smartdocs_category","embeddable":true,"href":"https:\/\/genesys-offenburg.de\/en\/wp-json\/wp\/v2\/smartdocs_category?post=23202"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}